EHS glossary>Safety term

The Definition of Fault Tree Analysis (FTA)

Fault tree analysis (FTA) is a top-down risk analysis method that starts with an undesired event and maps, with AND and OR logic gates, every combination of failures that could cause it.

Plain-English definition
Real-world example
Fault Tree Analysis (FTA) definition

Definition of Fault Tree Analysis (FTA)

Fault tree analysis (FTA) is a deductive, top-down method for finding how a specific unwanted event, called the top event, could happen. Analysts work backward from the top event and map all the equipment failures, human errors and conditions that could lead to it, linking them with logic gates in a tree-shaped diagram.

FTA was developed in the early 1960s at Bell Telephone Laboratories to study launch control safety for the Minuteman missile system. It was later adopted in aerospace, nuclear power, chemical processing, rail, automotive and medical devices. In occupational and process safety, it is used to study high-consequence events such as explosions, toxic releases and safety system failures.

Why Fault Tree Analysis Matters

For rare but catastrophic events, there is often no history to learn from. FTA lets teams work out in advance how such an event could happen, which combinations of failures would be needed, and where the system is weakest. It turns a vague worry into a clear map of causes.

FTA is especially good at exposing hidden single points of failure, such as two safeguards that share one sensor or one power supply. Finding those weaknesses on paper is far cheaper than discovering them after an accident.

How Fault Tree Analysis Works

Main Elements

  • Top event: The undesired outcome being studied, such as a reactor overpressure or a crane load drop.
  • Intermediate events: Failures that result from combinations of lower-level events.
  • Basic events: The lowest-level causes, such as a valve failing to close or an operator missing an alarm.
  • AND gate: The output happens only if all inputs happen together.
  • OR gate: The output happens if any one input happens.

Steps

  • Define the system and top event: Set clear boundaries and assumptions.
  • Build the tree: Work down from the top event, asking what could directly cause each event.
  • Find minimal cut sets: Identify the smallest combinations of basic events that cause the top event. A single-event cut set is a single point of failure.
  • Quantify (optional): Assign failure probabilities to basic events to estimate the top event's likelihood.
  • Act on the results: Add redundancy, testing or other controls where cut sets are small or likely.

Uses and Limitations

Uses

  • Showing how independent layers of protection combine through AND gates.
  • Finding single points of failure.
  • Supporting safety integrity level and reliability studies.
  • Analyzing complex incidents after the fact.

Limitations

  • Focuses on one top event at a time.
  • Requires skill and good failure data for quantitative results.
  • Can miss common cause failures unless modeled on purpose.

Regulations and Standards

  • IEC 61025: The international standard for fault tree analysis.
  • OSHA PSM: 29 CFR 1910.119(e) lists fault tree analysis as one of the acceptable methods for a process hazard analysis.
  • Nuclear and aerospace: The US Nuclear Regulatory Commission's Fault Tree Handbook (NUREG-0492) and NASA's fault tree handbook are widely used references.

Good Practices for Fault Tree Analysis

  • Define one clear top event: A vague top event produces a vague tree.
  • Use a team: Include operators, maintenance and engineering.
  • Include human error: Model operator actions, not just hardware.
  • Model common causes: Look for failures that could defeat several branches at once, such as a shared power supply.
  • Check data sources: Document where failure rates come from.
  • Pair with other tools: Use HAZOP or FMEA to find events, then FTA to study the most serious ones.

Common Fault Tree Analysis Mistakes

  • Top events that are too broad: A top event like plant accident is too vague to analyze well.
  • Treating safeguards as independent when they are not: Shared sensors or utilities create hidden OR paths.
  • Leaving out maintenance and testing: Untested safeguards may already be failed when demanded.
  • Overtrusting the numbers: Probability results are only as good as the failure data used.
  • Not acting on findings: A finished tree only helps if recommendations are tracked to completion.

Example of Fault Tree Analysis

A chemical plant used FTA to study the top event of a storage tank overflow. The tree showed that overflow required the level control to fail AND both the high-level alarm and the independent high-high shutdown to fail. However, the minimal cut sets revealed that the alarm and the shutdown used the same level transmitter, so one transmitter failure could defeat both.

The plant installed a separate transmitter for the shutdown, added proof testing and updated its process hazard analysis.

Frequently Asked Questions: Fault Tree Analysis (FTA)

What is the top event in a fault tree?

The top event is the specific undesired outcome being studied, such as an explosion, release or equipment failure. The tree is built downward from it.

What is the difference between an AND gate and an OR gate?

An AND gate means all inputs must occur for the output to occur. An OR gate means any single input is enough.

What is a minimal cut set?

It is the smallest combination of basic events that will cause the top event. Cut sets with only one event are single points of failure.

How is FTA different from FMEA?

FTA works top-down from one unwanted event to its causes. FMEA works bottom-up, starting from each component's failure modes and asking what effects they have.

Is fault tree analysis qualitative or quantitative?

It can be either. A qualitative fault tree shows the logic and cut sets. A quantitative fault tree adds failure probabilities to estimate how likely the top event is.

What software is used for fault tree analysis?

Many commercial reliability and risk tools support FTA, and simple trees can be drawn by hand or in diagram software. The method matters more than the tool.

Related Terms

Part of SafetyIQ's EHS glossary: plain-English definitions of workplace health and safety terms.

> Keep learning

More EHS terms

Browse the full glossary >

> See it in action

Put these safety terms into practice with SafetyIQ

Capture hazards, run inspections, track training and close out corrective actions in one platform built for high-risk, field-heavy work.

Book my free demo
★★★★★
4.8 out of 5 stars on
G2
G2 High Performer, Fall 2026