EHS glossary>Safety term

The Definition of Safety Integrity Level (SIL)

Safety integrity level (SIL) is a rating from SIL 1 to SIL 4, defined in IEC 61508 and IEC 61511, that shows how much risk reduction a safety instrumented function must reliably provide.

Plain-English definition
Real-world example
Safety Integrity Level (SIL) definition

Definition of Safety Integrity Level (SIL)

A safety integrity level (SIL) is a measure of how reliably a safety function must work to reduce a specific risk to an acceptable level. SIL is rated from SIL 1, the lowest, to SIL 4, the highest. Each step up means roughly ten times more risk reduction and a lower allowed probability that the function fails when needed.

SIL applies to safety instrumented functions (SIFs), such as automatic shutdowns that close a valve on high pressure, trip a furnace on flame loss or stop a pump on high level. These functions are carried out by a safety instrumented system (SIS) made of sensors, a logic solver and final elements such as valves.

Why Safety Integrity Level Matters

Automatic shutdown systems are often the last engineered barrier before a fire, explosion or toxic release. If they fail when called on, there may be nothing left to stop the event. SIL gives engineers a clear target for how dependable each of those systems has to be.

SIL also helps avoid both under-protection and over-engineering. A sound SIL assessment shows where high-integrity systems are truly needed and where simpler safeguards are enough, helping companies spend money where it reduces the most risk.

How SIL Works

SIL Bands for Low-Demand Functions

For functions that are rarely called on, as in most process plants, SIL is defined by the average probability of failure on demand (PFDavg):

  • SIL 1: PFDavg from 0.01 to 0.1, a risk reduction factor of about 10 to 100.
  • SIL 2: PFDavg from 0.001 to 0.01, a risk reduction factor of about 100 to 1,000.
  • SIL 3: PFDavg from 0.0001 to 0.001, a risk reduction factor of about 1,000 to 10,000.
  • SIL 4: PFDavg from 0.00001 to 0.0001. SIL 4 is very rare in process industries.

For high-demand or continuous functions, such as many machine safety functions, SIL is based on the probability of dangerous failure per hour.

The SIL Life Cycle

  • Hazard analysis: Identify hazards, often through a HAZOP.
  • SIL determination: Decide the required SIL for each function using methods such as layer of protection analysis (LOPA), risk graphs or a risk matrix.
  • Design: Choose architecture, redundancy and certified components that meet the target.
  • Verification: Calculate PFDavg to prove the design meets the SIL.
  • Operation and maintenance: Proof test the function at set intervals and manage bypasses.
  • Management of change: Reassess SIL when the process changes.

Regulations and Standards

  • IEC 61508: The basic functional safety standard for electrical, electronic and programmable safety systems.
  • IEC 61511: The process industry standard, adopted in the US as ANSI/ISA 61511.
  • IEC 62061: Applies SIL to machinery control systems, alongside performance level under ISO 13849.
  • OSHA PSM: 29 CFR 1910.119 requires equipment to follow recognized and generally accepted good engineering practices. ISA 61511 is widely treated as one of these practices for safety instrumented systems.

Good Practices for SIL

  • Do not over-assign SIL: Higher SILs cost more and need more testing. Use sound analysis to set the target.
  • Keep layers independent: Sensors used for control should not double as safety sensors.
  • Proof test on schedule: Untested functions lose reliability over time.
  • Control bypasses: Use permits and time limits for any bypass of a safety function, linked to management of change.
  • Track demands and failures: Compare real data with design assumptions.
  • Train people: Make sure engineers and technicians are competent in functional safety.

Common SIL Mistakes

  • Treating SIL as a product label: Buying SIL-rated parts does not make the whole function meet SIL.
  • Skipping proof tests: Missed or shallow tests let hidden failures build up.
  • Leaving bypasses in place: Bypassed trips during startup or maintenance are a common cause of major incidents.
  • Sharing sensors with control: One failed transmitter can defeat both control and protection.
  • Not revisiting SIL after changes: Process changes can raise the risk beyond what the original design covered.

Example of SIL

A LOPA on a reactor feed system found that high pressure could rupture the vessel and that existing safeguards gave a risk reduction of only 10. The company's risk target required another factor of 100 or more, so the team specified a SIL 2 high-pressure trip that closes the feed valves.

The design used two pressure transmitters in a voting arrangement and a certified logic solver, with yearly proof tests. A test two years later found one transmitter stuck, which was replaced before the function was ever needed.

Frequently Asked Questions: Safety Integrity Level (SIL)

What does SIL stand for?

Safety integrity level. It rates the required reliability of a safety instrumented function from SIL 1 to SIL 4.

Which SIL is the highest?

SIL 4 is the highest and requires the most risk reduction. In the process industries, SIL 1 to SIL 3 are common and SIL 4 is rarely used.

How is the required SIL determined?

Through a risk assessment such as layer of protection analysis, a risk graph or a calibrated risk matrix, which compares the risk without the function to the risk the company will accept.

Is a SIL-rated device enough to meet SIL?

No. SIL applies to the whole safety function, including sensors, logic and final elements, plus design, testing and maintenance. A certified component is only one part.

What is the difference between SIL and PL?

SIL comes from IEC 61508, IEC 61511 and IEC 62061 and is common in process plants. Performance level (PL) comes from ISO 13849 and is common in machinery. Both rate the reliability of safety functions, and they can be roughly compared.

What is a proof test?

A proof test is a periodic test that checks a safety function for hidden failures, such as a stuck valve or failed sensor, so it can be repaired before it is needed in a real demand.

Related Terms

Part of SafetyIQ's EHS glossary: plain-English definitions of workplace health and safety terms.

> Keep learning

More EHS terms

Browse the full glossary >

> See it in action

Put these safety terms into practice with SafetyIQ

Capture hazards, run inspections, track training and close out corrective actions in one platform built for high-risk, field-heavy work.

Book my free demo
★★★★★
4.8 out of 5 stars on
G2
G2 High Performer, Fall 2026