EHS glossary>Safety term

The Definition of Shock Protection Boundaries

Shock protection boundaries are distances set in NFPA 70E, the limited and restricted approach boundaries, that control how close people may come to exposed energized electrical parts based on their training and protection.

Plain-English definition
Real-world example
Shock Protection Boundaries definition

Definition of Shock Protection Boundaries

Shock protection boundaries are approach distances around exposed energized electrical conductors or circuit parts. They control who may come close to live parts and what protection they need. NFPA 70E defines two shock boundaries: the limited approach boundary and the restricted approach boundary. A separate arc flash boundary addresses burn hazards from an arc flash.

The boundaries exist because electric shock can happen without touching a conductor. At higher voltages, current can arc across air gaps, and a tool, ladder or body part can slip into contact in an instant.

Why Shock Protection Boundaries Matter

Many electrical injuries happen to people who were not working on the equipment at all, such as a helper, painter or passerby who stepped too close to an open panel. Boundaries give everyone a clear, physical line that marks where the danger starts and who is allowed inside.

They also guide PPE and planning. Knowing the boundaries for each piece of equipment tells qualified workers when they need rubber insulating gloves, insulated tools and a documented plan, and when an energized work permit may be required.

The Two Shock Boundaries

Limited Approach Boundary

The limited approach boundary is the distance from an exposed live part within which a shock hazard exists. Unqualified persons may not cross it unless they are continuously escorted and advised by a qualified person. It is set further out for movable conductors, such as overhead lines that can swing, than for fixed circuit parts.

Restricted Approach Boundary

The restricted approach boundary is the closer distance within which there is an increased likelihood of shock from arc-over or accidental movement. Only qualified persons may cross it, and they must have an approved plan, use shock-protective PPE such as rubber insulating gloves, and position themselves to keep body parts out of the boundary as much as possible.

Typical AC Distances

NFPA 70E gives boundary distances in tables by voltage. Common examples for alternating current systems include:

  • 50 to 150 volts: Limited approach of 3 feet 6 inches for fixed circuit parts and 10 feet for exposed movable conductors. The restricted approach is to avoid contact.
  • 151 to 750 volts: Limited approach of 3 feet 6 inches for fixed parts and 10 feet for movable conductors. Restricted approach of 1 foot.
  • Higher voltages: Distances increase with voltage, and the tables should be checked for each system.

Regulations and Standards

  • NFPA 70E: Article 130 sets the shock risk assessment process and boundary tables. Older editions also included a prohibited approach boundary, which was removed in the 2015 edition.
  • OSHA: 29 CFR 1910.333 requires safe work practices around live parts and lists approach distances for qualified persons in 1910.333(c). 1910.269 and construction rules cover power generation, transmission and distribution work, including minimum approach distances.
  • Overhead lines: Equipment and workers near overhead power lines must also follow separate clearance rules, such as 29 CFR 1926 Subpart CC for cranes.

Good Practices for Shock Protection Boundaries

  • De-energize first: Boundaries matter most when live work is truly justified under an energized work permit.
  • Mark the boundaries: Use barricades, tape or signs so unqualified workers stay out.
  • Label equipment: Include voltage and boundary information on equipment labels.
  • Use insulated tools: Inside the restricted boundary, use rated gloves, sleeves and insulated tools.
  • Escort visitors: Keep unqualified people outside the limited approach boundary unless escorted.
  • Train both groups: Qualified and unqualified workers should know what the boundaries mean.

Common Boundary Mistakes

  • Opening panels without barricades: Unqualified workers can wander into the limited approach boundary.
  • Forgetting conductive tools and materials: Ladders, tape measures and long tools can reach across boundaries.
  • Confusing arc flash and shock boundaries: Meeting one does not mean the other is satisfied.
  • Using generic distances: Boundaries depend on voltage, so check the right table for each system.
  • Damaged rubber gloves: Gloves must be air tested before use and periodically electrically tested.

Example of Shock Protection Boundaries

An electrician opened a 480-volt motor control center to take voltage readings. A painter working nearby walked over to watch and leaned within a foot of the open bucket. The electrician stopped work, but the near miss showed there was no barrier to keep unqualified workers back.

The facility began barricading the limited approach boundary, 3 feet 6 inches around open equipment, before any panel was opened, assigned an attendant for longer tasks and added boundary awareness to annual training for all trades.

Frequently Asked Questions: Shock Protection Boundaries

What is the limited approach boundary?

It is the distance from an exposed energized part within which a shock hazard exists. Unqualified persons may not cross it unless escorted by a qualified person.

What is the restricted approach boundary?

It is the closer distance where there is an increased risk of shock. Only qualified persons with proper PPE and a plan may cross it.

What happened to the prohibited approach boundary?

It was removed from NFPA 70E in the 2015 edition. The limited and restricted approach boundaries remain.

Is the arc flash boundary a shock boundary?

No. The arc flash boundary is based on burn risk from an arc flash, not shock. It can be larger or smaller than the shock boundaries, so both must be considered.

What is the limited approach boundary for 480 volts?

Under the NFPA 70E AC table, for 151 to 750 volts the limited approach boundary is 3 feet 6 inches for fixed circuit parts and 10 feet for exposed movable conductors. The restricted approach boundary is 1 foot.

Who is a qualified person for electrical work?

A qualified person has the skills and knowledge related to the equipment and has received safety training to identify and avoid the electrical hazards involved, as defined by OSHA and NFPA 70E.

Related Terms

Part of SafetyIQ's EHS glossary: plain-English definitions of workplace health and safety terms.

> Keep learning

More EHS terms

Browse the full glossary >

> See it in action

Put these safety terms into practice with SafetyIQ

Capture hazards, run inspections, track training and close out corrective actions in one platform built for high-risk, field-heavy work.

Book my free demo
★★★★★
4.8 out of 5 stars on
G2
G2 High Performer, Fall 2026